Viper 5101 installation guide download

My son played with it, now when i open or close my doors with the remote the alarm makes no noise. Viper is the world's best selling vehicle security and remote start brand. Once the engine begins running, let it run for at least 30 seconds. It shows the components of the circuit as simplified shapes, and the faculty and signal contacts in the middle of the devices.

Need manual wiring diagram to move from one car to. This hyundai sante fe gave me problems installing, including the drivers unlock wire, but i eventually sorted it all out and it worked great all winter. Hit start and the unit clicks and the dash lights come on but it will not engage the starter.

The toggle switch will only disable the remote start feature of your system. After changing the battery, the remote start will not work. It could be one of the 4 things listed here:.

Before we try starting car you must change some programming on the viper Grey hood pin wire is getting ground. My husband has a remote start the dealership put in, and if you're not close to the vehicle to hear the horn beep, you're out of luck.

Automotive wiring diagrams pertaining to viper remote start wiring diagram, image size x px, and to view image details please click the image. The remote control is small and easy to use, and is powered by an easily replaceable coin cell battery. A wiring diagram usually gives instruction approximately the relative outlook and. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. The advantage to using a D2D interface is that there is less wiring involved in the installation.

Check the XK module installation guide to determine which wires are not needed, and which options are available. Many new vehicles use low-voltage or multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic probes computer safe test lights.

Page Component Locations And Finding Wires Component locations and finding wires For detailed information on where to locate components, and how to find the wires you need, please refer to the Direct Tech web site at www. Making your wiring connections Before making your connections, plan how your wires will be routed through the vehicle.

Page Heavy Gauge Remote Start, H3 8-Pin Connector There are three harness connections relative to remote start function, including the heavy gauge and input and output harnesses. It outputs a single pulse when locking the doors with the remote, and two pulses when unlocking with the remote. This wire also outputs pulses for 30 seconds when Panic Mode is activated. Ground all your compo- nents to the same point in the vehicle, preferably the kick panel.

Scrape away any paint and use a factory bolt or make your own ground with a self-tapping screw and a star washer. When this wire receives an input for a minimum of. This is useful on vehicles that have a factory security system, it notifies the owner that the system was triggered.

This output is only intended to drive a relay. It cannot be connected directly to the dome light circuit, as the output cannot support the current draw of one or more light bulbs. See Set- ting the light flash polarity section of this guide for polarity settings. See descriptions for Aux 3 Warning! Never use this wire to drive anything but a relay or a low-current input, supplied output is only mA.

This type of output additionally stops and resets whenever the ignition is turned On and then Off. Page 23 Note: A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicator and the ECM. See the following diagram for details.

All rights reserved. They are used to energize the ignition circuits in the vehicle. It is crucial to ensure that these connections are capable of handling the current demands. For this reason, Scotch-Locks, T-taps and other such connectors are strongly discouraged.

This is common on Toyota and Nissans which required the use of Tech Tip document If this unit is being installed in a manual transmission vehicle then connect it to the emergency brake wire. This input will disable or shut down the remote start when the hood is opened. See Feature Descriptions, Menu 1 feature 11 for details about programming.

See Feature programming Menu 3, feature 8. If so, no door lock interface wiring is required. There are eight different types of door lock systems Type A - H. Page Neutral Safety Switch Interface Neutral safety switch interface Some vehicles do not have an electrical neutral safety switch. Instead, the ve- hicle has a mechanical neutral safety switch that physically interrupts the starter wire and is used when the vehicle is in any drive gear.

If the remote start is interfaced before this switch, it will provide protection from starting in gear. If the car does not start on the first attempt, let the remote start attempt again. Once the car starts, let it run until the parking lights come on. When the parking lights come on, shut off the remote start with the remote - that's it! Virtual Tach is programmed. Start the vehicle with the key. Viper remote start chevy malibu bcm connector diagram viper installation manual viper wiring diagram viper remote start.

C5 Tech - Installing a Viper remote start and looking wiring diagram or instuctions - Installing this on my 99 C5 Bought it here refurb for. Model Installation Guide Attempts to install this product by a person other than a.. For additional information and wiring diagrams see Docu-.

To exit timer mode without the transmitter: Make sure the remote start system is not operating the engine. Turn the ignition on.